18V ONE+ HP Brushless 30-34° Framing Nailer (RFN1830X)

The 18V ONE+ HP Brushless 30-34° Framing Nailer doesn’t need air when you take it out of the packaging. It’s ready to go straight out of the box.

The 18V ONE+ HP Brushless 30-34° Framing Nailer Air-Strike system doesn’t need gas cartridges to operate. It just uses compressed air and a ONE+ Battery. To top up your Framing Nailer with air, see: How to top up a RYOBI 18V ONE+ HP Brushless 30-34…

The RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer doesn’t have a bump fire mode.

How many nails the 18V ONE+ HP Brushless 30-34° Framing Nailer can drive per charge depends on the capacity (Ah) of the battery you’re using. The higher the Ah rating the more nails per charge. As a guide, a fully charged 4.0Ah battery will fire…

This depends on the capacity (Ah) of the battery you’re using. The higher the Ah rating the more nails per charge. As a guide, a fully charged 4.0Ah battery will fire up to approximately 750 nails.

The RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer magazine is designed to only fit one strip of nails at a time. For a nail diameter of 2.87mm, the maximum cutting capacity is 70 nails. For a nail diameter of 3.03mm, the maximum cutting capacity…

The RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer needs to be topped up with air after 20,000 - 25,000 nails are used.

The RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer has a 1 second ramp-up time. This means there is little to no delay between firing nails.

To adjust the nail depth using a RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, locate the dial at the nose piece, and rotate it anti-clockwise to increase the depth.

To fire nails with a RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, first turn on the Nailer by squeezing the grip switch located under the main trigger. The LED will glow green for 10 seconds, indicating the tool is ready to use. For safety…

To load nails into the RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, pointing forwards, insert one strip of nails, at the end of the magazine. Pull the tensioner all the way back and release it into place.

To maximise trouble-free operation with your RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, it’s recommended you maintain your Framing Nailer on a regular basis. Lubricate the firing pin with a couple of drops of pneumatic tool oil or similar.…

To operate a RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, position the nosepiece where you want to drive the nail. Then, press the tool to compress the nosepiece. The nosepiece must be fully depressed combined with the grip switch, or the…

If there is a nail jammed in your RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, the LED will flash red to indicate it’s in jam protection mode. To remove the nail, first remove the battery – this will reset the tool. Using the on-board Allen…

To remove unused nails from a 18V ONE+ HP Brushless 30-34° Framing Nailer, first pull the retainer back. Then push the lever on its side to allow the nails to slide out.

To top up a RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer with air, first remove the battery. Use the on-board Allan key to remove this cover to access the inlet valve - this looks like a car or bicycle tyre. To top up the air, use an Inflator…